Home > Not Working > Santro Indicator Not Working

Santro Indicator Not Working

Contents

I am worried because i heard that they are too expensive , even for checking they charge huge amount of fees and in the end they say k sab new daal PM for details Reply With Quote + Reply to Thread Page 1 of 5 123 ... Drive carefully, the life you save may be your own. Because the assembly fits over the steering column, you have to remove the steering wheel first. Check This Out

After that the fuel-gauge behaves very erratically, frequently reducing all the way to empty, climbing back up to the Full mark and then going back down to empty. Many modern headlamps have one fuse per headlamp. Broken stalks Roughen up the end of the stalk and the inside of the hole to give a good key for the glue. Ask your question now. https://gearheads.in/showthread.php?10758-Indicators-not-working-but-hazard-lights-are-perfectly-fine

Indicators Not Working But Hazards Are

The indicator flasher must have failed or not working properly.-approx cost -Rs- 200 2. I have changed relay and the headlight/flasherunit at the steering wheel but as soon as i turn the lights on the flasher lights continously to the left. Scott Prado 171.739 görüntüleme 2:50 How To Fix Fast Turn Signal/Blinker - Süre: 1:33. Follow the wiring from the switch down the steering column and disconnect it where it joins the main wiring loom by way of a multi-plug connector.

Daha fazla göster Dil: Türkçe İçerik konumu: Türkiye Kısıtlı Mod Kapalı Geçmiş Yardım Yükleniyor... I will rather get the sensor unit replaced than repaired. They not only improve your view of the road, they also make it much easier for other drivers to see your vehicle. Hyundai Excel Indicator Relay Check whether its giving any output the first time you turn the key in the morning.

ATTENTION Unregistered - Please take a note of our new Rules and Guidelines for Commercially Involved Members with immediate effect. Before refitting the switch, lubricate the mechanical parts with an electrical cleaning fluid. I am inclined to go with @ghpk. http://www.procarcare.com/includes/content/resourcecenter/encyclopedia/ch14/14TSTurnSignals.html Bu özellik şu anda kullanılamıyor.

There should be a wire near the tank with a tan color - this is the "fuel sender feed wire", which indicates to the fuel gauge how much gas you have Hyundai Getz Indicator Relay Oturum aç 2 0 Bu videoyu beğenmediniz mi? If one of the wires has broken, fit in a new section - again it may be easier to remove the stalk first. Could it be a faulty Turn Signal Relay (Flasher Relay)?

Car Indicator Lights Not Working

Oturum aç Çeviri Yazısı İstatistikler 1.783 görüntüleme 1 Bu videoyu beğendiniz mi? http://mechanics.stackexchange.com/questions/27052/indicators-not-working-but-hazard-lights-working Your pictured sealed the deal! Indicators Not Working But Hazards Are I guess I am lucky, I dreaded changing the Combination switch which costs some 850 bucks for my Zen as far as I can remember. Indicators And Hazards Not Working Awesome Please select a category to choose from: - Cancel Default Category Join Date Jan 2011 Posts 526 FIXED- I spent some time studying the User Manual.

Bill Eaglerunner 7.240 görüntüleme 3:38 Harley Davidson quick and easy code check - Süre: 2:50. Repeat the test, this time moving the probe of the test meter to the right-hand terminal in the multi-plug and the stalk to the right-hand turn position. After about 100km (near 3/4 mark), the fuel gauge starts behaving sanely and then tracks the actual fuel remaining in the tank. Bu videoyu bir oynatma listesine eklemek için oturum açın. Indicators And Hazards Stopped Working

This was the solution in my specific instance but there are two other possible faults which could be to blame for indicators not working... Selling Vitz+local cars - compatible bluetooth Ecu Scantool, High-amp car chargers, Apple-certified Lightning Cables, etc. There are usually three wires attached to the indicator switch: one feed wire to the switch and two wires leading from it to feed the right- and left-hand circuits. this contact form Ask A Mechanic Over 10,000 questions answered!

Also did you replace the blown fuse with the same rating one? 2002 Tata Indica DLS. 2004 Suzuki Zen - A G13B eater. 2005 Suzuki Baleno - India's fastest Naturally Aspirated Turn Signal Not Working In some cases there may be more than one stalk mounted on the steering column. Reply With Quote 28-07-2012,09:28 PM #7 Nauman32 PakWheeler Follow Join Date Jul 2012 Location Faisalabad Age 26 Posts 206 Follows 0 Following 0 Mentioned 1 Post(s) Tagged 1 Thread(s) Problems Posted

Oturum aç Paylaş Daha fazla Bildir Videoyu bildirmeniz mi gerekiyor?

Removing a stalk If necessary remove the steering wheel first. Feb 1997 Bajaj KB125 RTZ 49K km Mar 2003 Tata Indica V2 LSi 130K km Jan 2007 Tata Safari 3.0 DiCOR EX 4x4 148K km Reply With Quote Send PM Thank you in advance. Turn Signal Not Working On One Side Tighten the securing screws.

Mark the position of the switch in relation to the steering column. Take care not to get the wiring caught up in the column. The picture below may help in identifying the flasher although the picture is from my Sonata. Reply With Quote 6th Jun 2012,23:32 #6 Beasta1.6S View Profile View Forum Posts Private Message View Blog Entries '10 FORD Fiesta not aware that he can set his status here!

Join us to find out! Last Jump to page: User Tag List « Previous Thread | Next Thread » Tags for this Thread ECU, ECU Repairing, EFI, Hyundai, Santro, santro plus View Tag Cloud Bookmarks Bookmarks Take the old switch along to help identify the correct replacement. On the majority of cars you have only to remove the steering column shroud to gain access to the indicator stalk switch mechanism.

Replacement parts If the stalk appears beyond repair check with your local main dealer to find out whether any component parts are available. Check your state’s laws for specific requirements, but first book a mechanic to perform a thorough inspection of the high beams so the issue may be promptly resolved.